When you try to enable, disable, or update Hyper-V technology, the process stops responding

When you try to enable, disable, or update Hyper-V technology, the process stops responding

Article ID : 950792
Last Review : March 31, 2008
Revision : 1.0

SYMPTOMS

After you enable, disable, or update Hyper-V technology on a Windows Server 2008-based computer, the process stops responding. When you try to enable or update Hyper-V, the computer stalls at Configuring Updates Stage 3 of 3. In this case, only 54 percent of the process is completed. When you try to disable Hyper-V, the computer stalls at Configuring Updates Stage 3 of 3. In this case, only 75 percent of the process is completed.

Back to the top

CAUSE

This problem occurs when the following conditions are true:

• You enabled, disabled, or updated Hyper-V on a Hewlett-Packard (HP) server.
• The HP Network Configuration Utility was installed.

Back to the top

RESOLUTION

To resolve this problem, follow these steps:

1. Shut down the computer.
2. Insert the installation CD for Windows Server 2008, and then start the computer from the CD.
3. Set your language preference, and then click Next.
4. Click Repair your computer.
5. Select the operating system that you want to repair, and then click Next.

Note You may have to provide disk controller drivers at this point. Click Load Drivers, and then enter the location for the disk controller drivers.

6. In the System Recovery Options dialog box, click the operating system that you want to repair, and then click Next.
7. In the Choose a recovery tool screen, select Command Prompt.
8. At the command prompt, type C:, and then press ENTER.
9. Type cd Program Files HP NCU, and then press ENTER.
10. Type ren cpqteam.dll cpqteam.dll.safe, and then press ENTER.
11. Type exit, and then press ENTER. The System Recovery Options screen is displayed.
12. Click Restart.
13. When the server restarts, the configuration of Hyper-V automatically continues.
14. When the configuration process is completed, follow these steps:

a. Open the C: Program Files HP NCU folder.
b. Rename the Cpqteam.dll.safe file to Cpqteam.dll.
15. Restart the computer.

To prevent this problem, uninstall the HP Network Configuration Utility before you enable, disable, or update Hyper-V.

Back to the top

MORE INFORMATION

Hyper-V updates will be distributed by using Windows Update. To help prevent you from experiencing this problem, Windows Update will not present Hyper-V updates to computers that have the HP Network Configuration Utility installed. For more information about the prerequisites to install and to update Hyper-V on HP servers, visit the following Microsoft Web site:

http://www.microsoft.com/windowsserver2008/en/us/hyperv-install.aspx (http://www.microsoft.com/windowsserver2008/en/us/hyperv-install.aspx)

For more information about Hyper-V, visit the following Microsoft Web site:

http://technet2.microsoft.com/windowsserver2008/en/servermanager/virtualization.mspx (http://technet2.microsoft.com/windowsserver2008/en/servermanager/virtualization.mspx)

The third-party products that this article discusses are manufactured by companies that are independent of Microsoft. Microsoft makes no warranty, implied or otherwise, about the performance or reliability of these products.

Back to the top


APPLIES TO
• Windows Server 2008 Datacenter
• Windows Server 2008 Enterprise
• Windows Server 2008 Standard

Back to the top

Keywords: 
kbuninstall kbinstallation kbexpertiseinter kbtshoot kbprb KB950792

Back to the top

 

Microsoft Knowledge Base Article

This article contents is Microsoft Copyrighted material.
Microsoft Corporation. All rights reserved. Terms of Use | Trademarks


You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.

AddThis Social Bookmark Button

Leave a Reply

*
To prove that you're not a bot, enter this code
Anti-Spam Image